BLOG

BLOG

Back to list


Automotive Clutch Hydraulic Parts for Hyundai Repair


2026-11-16


The automotive clutch hydraulic parts from Jinaofeng include the KA00173 MD-712383 clutch slave cylinder for Hyundai applications. The product page lists a 3/4 inch diameter, the JAF number JAF6130 and the clutch slave cylinder category. Jinaofeng also supplies brake wheel cylinders, clutch master cylinders, brake master cylinders, brake expander wheels, rocker arm shafts and calipers.

What the Part Does

A clutch slave cylinder converts the hydraulic pressure from the master cylinder into the movement that releases the clutch. When the driver presses the pedal, the master cylinder pushes fluid through the line, and the slave cylinder pushes the release fork or the bearing. A worn slave cylinder can leak, lose the pedal or make the clutch engage late.

The buyer should match the part to the vehicle, the engine and the transmission. The page lists the Hyundai application and the model numbers, so the buyer can check the OE number and the JAF number against the old unit. A part that fits the thread but has a different bore can change the pedal feel and the release point.

Fit and Bore

The page lists a 3/4 inch diameter. The bore decides the force and the travel: a larger bore gives more force but less travel, and a smaller bore gives more travel but less force. The buyer should confirm the bore and the stroke with the original part, because a mismatch can cause a dragging or a slipping clutch.

Symptoms and Diagnosis

A leaking slave cylinder usually shows a wet boot or a drop in the fluid level. A pedal that goes to the floor, or a pedal that needs to be pumped, is a sign that air has entered the system. The workshop should check the master cylinder and the line before it replaces the slave, because a leak at the master can look like a slave fault.

A noisy release bearing and a slipping clutch can also be caused by a worn clutch, not only by the hydraulics. The buyer should ask the workshop to confirm the fault before the part is ordered.

Seals and Fluid

A clutch hydraulic part uses a rubber seal that must be compatible with the brake fluid. The buyer should confirm the seal material and the fluid specification. A mineral oil in a system designed for glycol fluid will swell the seal and cause a leak.

The system should be flushed when a new slave cylinder is fitted, because debris from the old part can damage the new seal. The buyer should include the bleed procedure in the installation instruction.

Materials and Finish

The page does not list the body material or the finish. A cast iron or an aluminum body with a honed bore is common, and the piston and the seal are the wear parts. The buyer should ask for the material, the bore finish and the corrosion protection for the market.

Quality Control

The part should be tested for the bore diameter, the seal leak, the stroke and the thread. The buyer should ask for the inspection report and should set an AQL with the supplier. A part that leaks on the test bench will leak in the vehicle.

Installation

The slave cylinder should be fitted with a new seal and a clean fluid. The push rod should be aligned with the release fork, and the mounting bolts should be tightened to the specified torque. The system should be bled until the pedal is firm, and the pedal should be checked again after a short drive.

Packing and Service

The part should be packed with a cap on the port and a plug on the bore, so the seal is not damaged in transit. The buyer should confirm the inner bag, the label and the carton quantity. A workshop that fits several parts a month should keep the OE and the JAF reference on the label.

Applications and Ordering

The part is used in aftermarket repair and replacement. Jinaofeng is based in the Ocean Economic Development Zone, Kanmen Xuanmen Phase III, Yuhuan City, Taizhou City, Zhejiang Province, China. The buyer should send the vehicle model, the year, the OE number and the quantity. The company can be reached by email at jaf1855@cnjaf.com or by phone at 0086-576-87568321.

Send the old unit photo and the vehicle data with the inquiry, and the team will confirm the part, the seal and the packing before a quotation is issued.

Previous page:

related blog